Beckett AF Manual de Instruções Página 9

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 24
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 8
9
AFG Burner Manual
If the nozzle is already installed, remove the nozzle
line assembly to verify that the nozzle size and
spray pattern are correct for the application (per
appliance manufacturer’s information). Verify that
the electrode tip settings comply with Figure 3.
If the nozzle is not installed, obtain a nozzle from
the manufacturer, having the capacity and spray
angle speci ed in the appliance manufacturer’s
information. For conversions or upgrades, when
information is not available for the application:
Refer to Table 6 to select the mid-range nozzle
spray angle for the head type being used.
Fire the burner and make sure the combustion
is acceptable and the ame is not impinging on
chamber surfaces.
If a shorter ame is needed, select a wider spray
angle. If a longer ame is needed, select a
narrower spray angle.
Either hollow or solid spray patterns may be
used. If combustion results are not satisfactory
with the selected spray pattern, try the other
pattern.
3.
4.
points up. Pull the nozzle line assembly toward you
and remove assembly from burner.
To replace the nozzle assembly, reverse the above
steps.
Mount Burner on Appliance
Mounting options
Bolt the burner to the appliance using the factory-
mounted ange or an adjustable ange.
Mounting dimensions
When using the Beckett universal adjustable ange,
mount the air tube at a 2° downward pitch unless
otherwise speci ed by the appliance manufacturer.
Verify that the air tube installed on the burner
provides the correct insertion depth. See Figure 7.
The end of the air tube should normally be ¼” back
from the inside wall of the combustion chamber.
Never allow the leading edge of the head assembly
to extend into the chamber, unless otherwise
speci ed by the heating appliance manufacturer.
Carefully measure the insertion depth when using
an adjustable ange. Verify the insertion depth
when using a welded ange.
7.
1.
1.
2.
3.
Table 6. Nozzle Spray Angles
Recommended nozzle spray angles
“F” head 70° or 80° nozzle
“L1” & “L2” head 45°, 60°, or 70° nozzle
“V1” head 45°, 60°, or 70° nozzle
Figure 3. – Electrode Tip Adjustment
Standard Dimensions for F, L1, and V1 Heads.
The Dimensions shown below are for use with L2 heads
and M series air tube combinations ending with an ‘N’
suf x (example: AFG70MDAQ
N)
Check/adjust electrodes
Check the electrode tip settings. Adjust if necessary
to comply with the dimensions shown in Figure 3. To
adjust, loosen the electrode clamp screw and slide/rotate
electrodes as necessary. Securely tighten the clamp
screw when nished.
Servicing nozzle line assembly
Turn off power to burner before proceeding.
Disconnect oil connector tube from nozzle line.
Loosen the two screws securing igniter retaining
clips and rotate both clips to release igniter
baseplate. Then tilt igniter back on its hinge.
Remove splined nut.
“F” head air tube. - Remove nozzle line assembly
from burner, being careful not to damage the
electrodes or insulators while handling. To ease
removal of long assemblies (over 9 inches), rotate
assembly 180° from installed position after pulling
partially out of tube.
“L1, “L2, and “V1” head air tubes. - Slide nozzle
line assembly forward (further into air tube) so the
head clears the venturi opening. Then rotate the
nozzle line assembly 90° so the nozzle line end
1.
2.
3.
4.
5.
6.
Section: Mount Burner on Appliance
Vista de página 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comentários a estes Manuais

Sem comentários

AEG Santo 1742E-m3D(R) manuály

Uživatelské manuály a uživatelské příručky pro ne AEG Santo 1742E-m3D(R).
Poskytujeme 1 manuály pdf AEG Santo 1742E-m3D(R) ke stažení zdarma podle typů dokumentů: Uživatelský manuál






Další produkty a příručky pro ne AEG

Modely Typ Dokumentu
ARCTIS No-frost (frost free) Uživatelský manuál      AEG ARCTIS No-frost (frost free) User manual [de] [es] [fr] [it] [nl] [pl] , 64 stránky
SCT71900S0 Uživatelský manuál SCT71900S0 SV KYL-FRYS BRUKSANVISNING, 28 stránky
HES 4890 DVB-T/DVD Uživatelský manuál   Braunschweiger, 32 stránky
66050i Technické informace   AEG 66050i Technical information, 60 stránky
818 20 85 Provozní pokyny   AEG 818 20 85 Operating instructions, 48 stránky
SKZ71800F0 Uživatelský manuál     SKZ71800F0 CSNávod k použití 2 NOBruksanvisning - E, 92 stránky
Integrating Freezer Provozní pokyny   AEG Integrating Freezer Operating instructions, 13 stránky
C 8 16 41 I Uživatelský manuál   Catalogue, 48 stránky
SANTO 75448 KGR Uživatelský manuál   AEG SANTO 75448 KGR User manual, 24 stránky
S75358KG38 Uživatelský manuál     AEG S75358KG38 User manual, 64 stránky
SKD71800F0 Uživatelský manuál   AEG SKD71800F0 User manual, 16 stránky
ARE I2 Instalační příručka   AEG ARE I2 Installation guide, 33 stránky
SANTO Provozní pokyny   AEG SANTO Operating instructions, 44 stránky
SANTO 72358 KA Provozní pokyny   AEG SANTO 72358 KA Operating instructions [en] , 32 stránky
S83430CTX2 Uživatelský manuál       AEG S83430CTX2 User manual, 72 stránky
Automatic Refrigerator Příručka pro použití a péči   AEG Automatic Refrigerator Use & care guide, 15 stránky
Oko arctis 2682 GT Uživatelský manuál   Braunschweiger, 24 stránky
DL 80.2 M Uživatelský manuál   AEG DL 80.2 M Product data, 2 stránky
ARCTIS 1310GS Uživatelský manuál   ARCTIS 70258 GS, 21 stránky
AGS58200F0 Uživatelský manuál      AEG AGS58200F0 User manual, 72 stránky